Need to reset your GE universal remote?
The process is pretty easy and we can walk you through it.
Just follow the steps below to get started.
Steps To Reset GE Universal Remote
To reset your GE universal remote, press down and hold the Setup button until you notice the red light blinks for at least 2 seconds.
Release the button so the LED light remains on.
Then press and release the OK button.
Another method is to press the mute key and then press 0.
When you do this, your remote is restored to the factory state.
Programming GE Universal Remote
Enter the Code Manually
To program your GE universal remote, you’ll need to find the appropriate remote codes for your devices.
First, check the manual for the GE universal remote codes or look them up online.
Once you have the code, you should turn on the device you want to control.
Next, press down and hold the Setup button on your remote until you see the red light turns on.
Enter the code, and the red light will blink twice to confirm it’s the right code.
Your remote should now be paired with the device.
Code Search Method
If you can’t find the specific code for your device, don’t worry! The code search method will find it for you.
Turn on the device you want to control, press and hold the Setup button on your remote until the red light turns on, and then press the corresponding device button (e.g., TV, DVD, or CBL).
Now, press and release the Channel Up or Channel Down button until your device switches off.
Once your device turns off, press the Mute or Enter button to save the code.
Brand Code Search Method
Another method to program your GE universal remote is with the brand code search.
This method is particularly helpful when you know the brand of the device you wanna control.
Turn on the device, press down and hold the Setup button until you notice the red light turns on.
Press the device button (TV, DVD, or CBL) and enter one of the GE universal remote codes specific to your device’s brand.
The remote will cycle through the codes and send a signal to your device.
When your device turns off, press the Mute or Enter button to save the code.
Now, your remote should be programmed and ready for use.
Device Categories and Codes
When you want to control various devices with your GE universal remote, the first thing you gotta do is to find the proper device codes.
In this section, we’ll cover the main categories of devices and their associated codes for programming your remote.
TV Codes
Each TV brand comes with its code list to use with your GE universal remote.
To find the right code, you can look inside the user manual or visit the manufacturer’s website.
There, you can easily search for your TV model number and get the corresponding remote code.
DVD Player Codes
Similar to TVs, each DVD player brand and model has its own set of codes.
To find the remote code for your DVD player, again, refer to the user manual or check the manufacturer’s website.
Make sure to match up the device code with the exact model number of your DVD player.
Audio Device Codes
Just like TVs and DVD players, each audio device (soundbars, stereo systems, and other audio devices) brand and model requires a specific code. S
earch for your device’s model number in the user manual or on the manufacturer’s website to find the corresponding code.
Troubleshooting and Fixes
Remote Not Responding or Working
If your GE universal remote is not responding or working, follow these steps:
- Ensure the remote control is pointed directly at the TV or electronic device.
- Check if there are any obstructions between the remote and the TV.
- Verify the remote’s batteries are installed correctly and have power.
- Try re-entering the remote codes for your device.
- Test the remote’s buttons, like the mute or power button to see if any specific button is causing the issue.
- Replace the batteries if necessary and reset the remote if the problem persists.
Saving Programmed Codes
To save your programmed codes for your GE universal remote, follow these steps:
- After programming the codes, press the device button (such as the TV button) to save the code.
- Test the remote with your device (TV, audio, etc.) to make sure the code works properly.
- If the remote is not responding with the saved code, try programming other codes for your device.
- If all else fails, refer to the manual for the remote for specific instructions on saving codes.
Power Recycling the Remote
Power recycling your GE universal remote can help resolve any temporary issues.
Perform the following steps:
- Take out the batteries from the remote.
- Press and hold the power button on the remote for 20-30 seconds to discharge any residual power.
- Reinsert the batteries into the remote.
- If the remote doesn’t power on or the red LED light doesn’t illuminate, verify the batteries’ proper installation and ensure the batteries have enough power.
- Test the remote on your TV or other electronic devices to see if it is responding correctly.
- If the issue persists, try resetting the remote to factory settings and reprogramming it with the appropriate remote codes.
Frequently Asked Questions
Resetting GE remote steps?
To reset your GE universal remote, press down and hold the Setup button until you notice the red light blinks for at least 2 seconds.
Release the button so the LED light remains on.
Then press and release the OK button.
Another method is to press the mute key and then press 0.
When you do this, your remote is restored to the factory state.
Troubleshoot unresponsive remote?
If your remote is unresponsive, first check the batteries and replace them if necessary.
Ensure nothing is blocking the infrared sensor on the remote or the device.
If it still doesn’t work, try resetting the remote (as explained above) and reprogramming it with the appropriate codes.
Programming app buttons?
To program app buttons on your GE universal remote, press down and hold the Setup button until the desired device button (e.g., “TV”) blinks twice.
Enter the code from the code finder into your remote.
The red light will blink twice again to confirm the correct code.
Press the app button (e.g., “Netflix”) you want to program and enter the provided command codes.
GE remote without codes?
If you don’t have the codes for your GE remote, you can find them online using the version number of your remote (located on the white sticker inside the battery compartment).
Lookup the codes according to the version number and the device you wish to control.
Resetting RCA universal remote?
To reset an RCA universal remote, press and hold the Code Search or Setup button until the indicator light stays on.
Release the button and press down the device button (e.g., “TV”) you wish to reset.
Next, press down the Power button on the remote and keep pressing it until the device turns off.
Once it turns off, press the Enter button to save the reset.
DVD player codes for GE remote?
To find DVD player codes for your GE remote, locate the version number of your remote (as described earlier) and refer to the code finder or manual specific to your remote’s version.
Enter the DVD player code using the same process mentioned in “Programming app buttons?”